From: Linus Walleij <linus.walleij@linaro.org>
To: "Toke Høiland-Jørgensen" <toke@toke.dk>,
"Kalle Valo" <kvalo@kernel.org>,
"Arend van Spriel" <aspriel@gmail.com>,
"Franky Lin" <franky.lin@broadcom.com>,
"Hante Meuleman" <hante.meuleman@broadcom.com>,
"Andy Shevchenko" <andriy.shevchenko@linux.intel.com>,
"Arnd Bergmann" <arnd@arndb.de>, "Lee Jones" <lee@kernel.org>,
"Brian Norris" <briannorris@chromium.org>,
"Srinivasan Raju" <srini.raju@purelifi.com>
Cc: linux-wireless@vger.kernel.org, linux-kernel@vger.kernel.org,
brcm80211-dev-list.pdl@broadcom.com,
Linus Walleij <linus.walleij@linaro.org>
Subject: [PATCH 6/6] wifi: cw1200: Convert to GPIO descriptors
Date: Wed, 31 Jan 2024 23:37:25 +0100 [thread overview]
Message-ID: <20240131-descriptors-wireless-v1-6-e1c7c5d68746@linaro.org> (raw)
In-Reply-To: <20240131-descriptors-wireless-v1-0-e1c7c5d68746@linaro.org>
The CW1200 uses two GPIOs to control the powerup and reset
pins, get these from GPIO descriptors instead of being passed
as platform data from boardfiles.
The RESET line will need to be marked as active low as we will
let gpiolib handle the polarity inversion.
The SDIO case is a bit special since the "card" need to be
powered up before it gets detected on the SDIO bus and
properly probed. Fix this by using board-specific GPIOs
assigned to device "NULL".
There are currently no in-tree users.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
drivers/net/wireless/st/cw1200/cw1200_sdio.c | 42 +++++++++-------
drivers/net/wireless/st/cw1200/cw1200_spi.c | 71 ++++++++++++++++------------
include/linux/platform_data/net-cw1200.h | 4 --
3 files changed, 65 insertions(+), 52 deletions(-)
diff --git a/drivers/net/wireless/st/cw1200/cw1200_sdio.c b/drivers/net/wireless/st/cw1200/cw1200_sdio.c
index 4c30b5772ce0..00c4731d8f8e 100644
--- a/drivers/net/wireless/st/cw1200/cw1200_sdio.c
+++ b/drivers/net/wireless/st/cw1200/cw1200_sdio.c
@@ -8,7 +8,7 @@
#include <linux/module.h>
#include <linux/interrupt.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include <linux/mmc/host.h>
#include <linux/mmc/sdio_func.h>
@@ -178,12 +178,15 @@ static int cw1200_sdio_irq_unsubscribe(struct hwbus_priv *self)
return ret;
}
+/* Like the rest of the driver, this only supports one device per system */
+static struct gpio_desc *cw1200_reset;
+static struct gpio_desc *cw1200_powerup;
+
static int cw1200_sdio_off(const struct cw1200_platform_data_sdio *pdata)
{
- if (pdata->reset) {
- gpio_set_value(pdata->reset, 0);
+ if (cw1200_reset) {
+ gpiod_set_value(cw1200_reset, 0);
msleep(30); /* Min is 2 * CLK32K cycles */
- gpio_free(pdata->reset);
}
if (pdata->power_ctrl)
@@ -196,16 +199,21 @@ static int cw1200_sdio_off(const struct cw1200_platform_data_sdio *pdata)
static int cw1200_sdio_on(const struct cw1200_platform_data_sdio *pdata)
{
- /* Ensure I/Os are pulled low */
- if (pdata->reset) {
- gpio_request(pdata->reset, "cw1200_wlan_reset");
- gpio_direction_output(pdata->reset, 0);
+ /* Ensure I/Os are pulled low (reset is active low) */
+ cw1200_reset = devm_gpiod_get_optional(NULL, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(cw1200_reset)) {
+ pr_err("could not get CW1200 SDIO reset GPIO\n");
+ return PTR_ERR(cw1200_reset);
}
- if (pdata->powerup) {
- gpio_request(pdata->powerup, "cw1200_wlan_powerup");
- gpio_direction_output(pdata->powerup, 0);
+ gpiod_set_consumer_name(cw1200_reset, "cw1200_wlan_reset");
+ cw1200_powerup = devm_gpiod_get_optional(NULL, "powerup", GPIOD_OUT_LOW);
+ if (IS_ERR(cw1200_powerup)) {
+ pr_err("could not get CW1200 SDIO powerup GPIO\n");
+ return PTR_ERR(cw1200_powerup);
}
- if (pdata->reset || pdata->powerup)
+ gpiod_set_consumer_name(cw1200_powerup, "cw1200_wlan_powerup");
+
+ if (cw1200_reset || cw1200_powerup)
msleep(10); /* Settle time? */
/* Enable 3v3 and 1v8 to hardware */
@@ -226,13 +234,13 @@ static int cw1200_sdio_on(const struct cw1200_platform_data_sdio *pdata)
}
/* Enable POWERUP signal */
- if (pdata->powerup) {
- gpio_set_value(pdata->powerup, 1);
+ if (cw1200_powerup) {
+ gpiod_set_value(cw1200_powerup, 1);
msleep(250); /* or more..? */
}
- /* Enable RSTn signal */
- if (pdata->reset) {
- gpio_set_value(pdata->reset, 1);
+ /* Deassert RSTn signal, note active low */
+ if (cw1200_reset) {
+ gpiod_set_value(cw1200_reset, 0);
msleep(50); /* Or more..? */
}
return 0;
diff --git a/drivers/net/wireless/st/cw1200/cw1200_spi.c b/drivers/net/wireless/st/cw1200/cw1200_spi.c
index c82c0688b549..9df7f46588b4 100644
--- a/drivers/net/wireless/st/cw1200/cw1200_spi.c
+++ b/drivers/net/wireless/st/cw1200/cw1200_spi.c
@@ -11,7 +11,7 @@
*/
#include <linux/module.h>
-#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
#include <linux/delay.h>
#include <linux/spinlock.h>
#include <linux/interrupt.h>
@@ -38,6 +38,8 @@ struct hwbus_priv {
const struct cw1200_platform_data_spi *pdata;
spinlock_t lock; /* Serialize all bus operations */
wait_queue_head_t wq;
+ struct gpio_desc *reset;
+ struct gpio_desc *powerup;
int claimed;
};
@@ -275,12 +277,12 @@ static void cw1200_spi_irq_unsubscribe(struct hwbus_priv *self)
free_irq(self->func->irq, self);
}
-static int cw1200_spi_off(const struct cw1200_platform_data_spi *pdata)
+static int cw1200_spi_off(struct hwbus_priv *self, const struct cw1200_platform_data_spi *pdata)
{
- if (pdata->reset) {
- gpio_set_value(pdata->reset, 0);
+ if (self->reset) {
+ /* Assert RESET, note active low */
+ gpiod_set_value(self->reset, 1);
msleep(30); /* Min is 2 * CLK32K cycles */
- gpio_free(pdata->reset);
}
if (pdata->power_ctrl)
@@ -291,18 +293,12 @@ static int cw1200_spi_off(const struct cw1200_platform_data_spi *pdata)
return 0;
}
-static int cw1200_spi_on(const struct cw1200_platform_data_spi *pdata)
+static int cw1200_spi_on(struct hwbus_priv *self, const struct cw1200_platform_data_spi *pdata)
{
/* Ensure I/Os are pulled low */
- if (pdata->reset) {
- gpio_request(pdata->reset, "cw1200_wlan_reset");
- gpio_direction_output(pdata->reset, 0);
- }
- if (pdata->powerup) {
- gpio_request(pdata->powerup, "cw1200_wlan_powerup");
- gpio_direction_output(pdata->powerup, 0);
- }
- if (pdata->reset || pdata->powerup)
+ gpiod_direction_output(self->reset, 1); /* Active low */
+ gpiod_direction_output(self->powerup, 0);
+ if (self->reset || self->powerup)
msleep(10); /* Settle time? */
/* Enable 3v3 and 1v8 to hardware */
@@ -323,13 +319,13 @@ static int cw1200_spi_on(const struct cw1200_platform_data_spi *pdata)
}
/* Enable POWERUP signal */
- if (pdata->powerup) {
- gpio_set_value(pdata->powerup, 1);
+ if (self->powerup) {
+ gpiod_set_value(self->powerup, 1);
msleep(250); /* or more..? */
}
- /* Enable RSTn signal */
- if (pdata->reset) {
- gpio_set_value(pdata->reset, 1);
+ /* Assert RSTn signal, note active low */
+ if (self->reset) {
+ gpiod_set_value(self->reset, 0);
msleep(50); /* Or more..? */
}
return 0;
@@ -381,20 +377,33 @@ static int cw1200_spi_probe(struct spi_device *func)
spi_get_chipselect(func, 0), func->mode, func->bits_per_word,
func->max_speed_hz);
- if (cw1200_spi_on(plat_data)) {
+ self = devm_kzalloc(&func->dev, sizeof(*self), GFP_KERNEL);
+ if (!self) {
+ pr_err("Can't allocate SPI hwbus_priv.");
+ return -ENOMEM;
+ }
+
+ /* Request reset asserted */
+ self->reset = devm_gpiod_get_optional(&func->dev, "reset", GPIOD_OUT_HIGH);
+ if (IS_ERR(self->reset))
+ return dev_err_probe(&func->dev, PTR_ERR(self->reset),
+ "could not get reset GPIO\n");
+ gpiod_set_consumer_name(self->reset, "cw1200_wlan_reset");
+
+ self->powerup = devm_gpiod_get_optional(&func->dev, "powerup", GPIOD_OUT_LOW);
+ if (IS_ERR(self->powerup))
+ return dev_err_probe(&func->dev, PTR_ERR(self->powerup),
+ "could not get powerup GPIO\n");
+ gpiod_set_consumer_name(self->reset, "cw1200_wlan_powerup");
+
+ if (cw1200_spi_on(self, plat_data)) {
pr_err("spi_on() failed!\n");
- return -1;
+ return -ENODEV;
}
if (spi_setup(func)) {
pr_err("spi_setup() failed!\n");
- return -1;
- }
-
- self = devm_kzalloc(&func->dev, sizeof(*self), GFP_KERNEL);
- if (!self) {
- pr_err("Can't allocate SPI hwbus_priv.");
- return -ENOMEM;
+ return -ENODEV;
}
self->pdata = plat_data;
@@ -416,7 +425,7 @@ static int cw1200_spi_probe(struct spi_device *func)
if (status) {
cw1200_spi_irq_unsubscribe(self);
- cw1200_spi_off(plat_data);
+ cw1200_spi_off(self, plat_data);
}
return status;
@@ -434,7 +443,7 @@ static void cw1200_spi_disconnect(struct spi_device *func)
self->core = NULL;
}
}
- cw1200_spi_off(dev_get_platdata(&func->dev));
+ cw1200_spi_off(self, dev_get_platdata(&func->dev));
}
static int __maybe_unused cw1200_spi_suspend(struct device *dev)
diff --git a/include/linux/platform_data/net-cw1200.h b/include/linux/platform_data/net-cw1200.h
index c510734405bb..89d0ec6f7d46 100644
--- a/include/linux/platform_data/net-cw1200.h
+++ b/include/linux/platform_data/net-cw1200.h
@@ -14,8 +14,6 @@ struct cw1200_platform_data_spi {
/* All others are optional */
bool have_5ghz;
- int reset; /* GPIO to RSTn signal (0 disables) */
- int powerup; /* GPIO to POWERUP signal (0 disables) */
int (*power_ctrl)(const struct cw1200_platform_data_spi *pdata,
bool enable); /* Control 3v3 / 1v8 supply */
int (*clk_ctrl)(const struct cw1200_platform_data_spi *pdata,
@@ -30,8 +28,6 @@ struct cw1200_platform_data_sdio {
/* All others are optional */
bool have_5ghz;
bool no_nptb; /* SDIO hardware does not support non-power-of-2-blocksizes */
- int reset; /* GPIO to RSTn signal (0 disables) */
- int powerup; /* GPIO to POWERUP signal (0 disables) */
int irq; /* IRQ line or 0 to use SDIO IRQ */
int (*power_ctrl)(const struct cw1200_platform_data_sdio *pdata,
bool enable); /* Control 3v3 / 1v8 supply */
--
2.34.1
next prev parent reply other threads:[~2024-01-31 22:37 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-01-31 22:37 [PATCH 0/6] Convert some wireless drivers to use GPIO descriptors Linus Walleij
2024-01-31 22:37 ` [PATCH 1/6] wifi: ath9k: Obtain system GPIOS from descriptors Linus Walleij
2024-02-01 10:57 ` Toke Høiland-Jørgensen
2024-02-01 11:40 ` Andy Shevchenko
2024-02-01 12:51 ` Kalle Valo
2024-02-01 12:20 ` Arnd Bergmann
2024-02-01 13:17 ` Andy Shevchenko
2024-02-01 14:00 ` Arnd Bergmann
2024-02-01 14:18 ` Toke Høiland-Jørgensen
2024-02-02 7:31 ` Arnd Bergmann
2024-02-02 10:23 ` Toke Høiland-Jørgensen
2024-02-05 18:13 ` Kalle Valo
2024-01-31 22:37 ` [PATCH 2/6] wifi: ti: wlcore: sdio: Drop unused include Linus Walleij
2024-02-05 18:17 ` Kalle Valo
2024-01-31 22:37 ` [PATCH 3/6] brcm80211: brcmsmac: Drop legacy header Linus Walleij
2024-01-31 22:37 ` [PATCH 4/6] wifi: mwifiex: Drop unused headers Linus Walleij
2024-01-31 22:37 ` [PATCH 5/6] wifi: plfxlc: Drop unused include Linus Walleij
2024-01-31 22:37 ` Linus Walleij [this message]
2024-02-01 10:02 ` [PATCH 6/6] wifi: cw1200: Convert to GPIO descriptors Kalle Valo
2024-02-01 11:42 ` [PATCH 0/6] Convert some wireless drivers to use " Andy Shevchenko
2024-02-01 12:53 ` Kalle Valo
2024-02-01 17:13 ` Linus Walleij
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240131-descriptors-wireless-v1-6-e1c7c5d68746@linaro.org \
--to=linus.walleij@linaro.org \
--cc=andriy.shevchenko@linux.intel.com \
--cc=arnd@arndb.de \
--cc=aspriel@gmail.com \
--cc=brcm80211-dev-list.pdl@broadcom.com \
--cc=briannorris@chromium.org \
--cc=franky.lin@broadcom.com \
--cc=hante.meuleman@broadcom.com \
--cc=kvalo@kernel.org \
--cc=lee@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=srini.raju@purelifi.com \
--cc=toke@toke.dk \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.